Contact Now
Please Leave Us A Message
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Jiaozuo Huafei Electronic & Electric Co., Ltd. ZhongKuang (Hainan) Technology Co., Ltd.
ginger@jzhfdq.com
+86-391-3567086
Model No.: GVD10
I. Overview
1. Product application and usage range
The sensor is used for the place under coal mine with coal dust and methane explosive gas, and is used as a tear detection for belt.
2. Product features
The sensor has reliable performance, simple structure, good safety performance, and easy to use and other characteristics.
3. Product Model and Significance
Explosion-proof type of sensor: Mining intrinsically safe type ExibI Mb
Sensor Model Explanation
4. Related devices
The related device of the sensor is KHP121A-Z coal mine explosion proof and intrinsically safe type controller of Belt Conveyor Protection device.
5. Ambient condition
5.1 Normal working condition
a) Altitude less than 2000m.
b) Ambient temperature within -5℃~+40℃.
c) Relative humidity not over 95% (25℃).
d) The place under mine with coal dust and methane explosive gas.
e) The place without corrosive gas which could damage metal and insulation.
5.2 The worst ambient condition of storage and transportation.
a) High temperature: +60℃.
b) Low temperature: -40℃.
c) Relative humidity not over 95% (25℃).
d) Vibration: accelerated speed 50m/s².
e) Impact: peak accelerated speed 500m/s².
II. Technical features
1. The technical parameters of the sensor are shown in table 1
Table 1
| Item | Performance and parameters |
| Contact mode | One pair of normal open, one pair of normal close |
| Contact capacity | DC 12.5V/0.5A (resistive load) |
| Action angle | 10° ±3° |
| Reset angle | 2°～5° |
| Action direction | Single direction |
| Contact resistance | ≤0.1Ω |
III. Structure features
The structure of tear sensor is shown in below figure. This sensor is mainly composed of feeler lever, transmission part and internal switch, etc. Size: 538mm×211mm×64mm. shell material: PA plastic. Weight:
IV. Working Process and Principle
When the coal gangue blocks or the bunker is full of coal, the coal level sensor at relative position contacts with coal, tilting the spring of the sensor, when it reaching to the action angle, the normal open contact in the sensor become close. When the coal level goes down, the spring rod tilt of the sensor recover to reset angle, the contact of the sensor reset automatically.
travel switch LX19K
V. Installation and wiring
The sensor should be installed between the up and down belt, and between two carrier rollers at the horizontal direction, it is better that the most flabby up belt could not touch the sensor. To fix the wirerope of the sensor on the both sides of the Belt Conveyor steel frame. In principle, install one sensor every 30~50m. This sensor include one set of accessory, which is connected by a φ10mm rebar, the installation should ensure that the sensor does not take misoperation and the action is reliable.
Cable outer diameter φ8~φ12( or communication cable is available), not less than 2.5mm².
VI. Usage attention
1. The structure and every electrical parameters of the sensor have been debugged before leaving the factory, the user shall not change its structure and electrical parameters at will to ensure the performance of protection, explosion-proof and intrinsically safe. This product can only be used with designated device, or the devices have explosion proof tested.
2. The detection of the belt tear up is determined by the sensor, and the sensor is installed after debugging, the working condition of the sensor directly determines whether belt tear up protection can work normally, and the non-professional personnel is not allowed to take off or install the sensor.
3. The maintenance personnel should regularly check the condition of each part of the sensor, the problems must be dealt with in time.
4. The improper changes of internal components wiring may cause equipment damage, our company does not bear the liability and economic losses caused by above-mentioned accident.
5. The packing carton can be used for all kinds of transportation including land and water under the condition of avoiding direct rain and snow.
6. The packaged device can be stored in the warehouses with air circulation, the temperature is (-10~40)℃, relative humidity not over 90% for more than 12 months.
7. Take out the packing list and compare with each item to confirm the conformity.
8. To check the nameplate on the sensor is comply with the order requirement.
Huafei Company could provide Different Kinds Of Sensors，such as complete Automatic Control Sensor, Mining Temperature Sensor for belt conveyor, Belt Conveyor Safety Protection, Belt Conveyor Sensor, belt conveyor automatic control sensor, Explosion Proof Sensor, Belt Conveyor Sensors and other Belt Conveyor Safety Protection.
Product Categories : Electric Aotumation > Belt Conveyor Control
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Fill in more information so that we can get in touch with you faster
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.